The PIR Sensor module allows you to sense motion. It is almost always used to detect the motion of a human body within the sensor's range. The PIR sensor module provides an output "HIGH" when a human body is detected within its range and an automatic Delay "LOW" when the body leaves its range. The delay time is adjustable using the potentiometer on-board. The minimum delay time that can be set is 5 seconds and maximum of 200 seconds. The blocking time potentiometer is also provided on-board to set the blocking time during which the sensor does not respond to any change in motion. The minimum blocking time that can be set is 2.5 seconds and maximum of 10 seconds.
Specifications:
   • Infrared sensor with control circuit board
   • The sensitivity and holding time can be adjusted
   • Detecting Range: Approx. 7m / 23 feet
   • Detecting Angle: Less than 100 degrees
   • Working Voltage Range: DC 5V- 20V
   • Quiescent Current: Less than 50uA
   • Level Output Voltage: High 3V / Low 0V .

CMOS Integrated DTMF Receiver/Decoder
The CM8870PI provides full DTMF receiver capability by integrating both the bandsplit filter and digital decoder functions into a single 18-pin DIP..

32K SERIAL I2C BUS EEPROM.

Generally used for De-soldering PCB components. Low cost and quality desoldering wire.
Length: 1 Meter (multiple quantity will get continuous one long piece), Width: approx. 2 mm..

High Quality Female To Female Single Core Full Shielded Jumper Wire with Protective Heat Shrink Sleeve for Very High Sensitive Low Level Signals, Microphone Signals, Tape Head, ADC Inputs, Sensor Signals, Analog Signals, Audio Signals etc.
End Terminals: Gold Plated Female Pins, Terminals Wire: Red-Signal Black-Ground (Shielding 99%), Length: 100cm, Wire: Chetan 14/44 SWG 1 Core, Jacket Sleeve Color: White, Black or Red..

Fabrication of White Plastic PVC Board Enclosure Project Box for electronic projects, power supply units, student projects, amplifiers, etc..
Outer Size: As Boards Size (which you choose) Inner Space Size: As Boards size - 2 x Board Thickness Note: First add minimum 4pcs (4 to 6pcs) boards cut size to cart as your requirement. This is Only Fabrication Charges.

Solid State Relay PCB with All Components.
Kit Components: (PCB 1pc, 1N4007 4pcs, MOC3041 1pc, IC Base 6-Pin 1pc, 5mm Red LED 1pc, 2-Pin Relimate Male 0.2" 1pc, 68 Ohm 1pc, 47 Ohm 1pc, 56 Ohm 1W 1pc, 330 Ohm 1W 1pc, 39 Ohm 1W 1pc, 0.01uF Capacitor 1pc, BTA12 1pc, Heatsink 1pc, PCB Terminal Block 2pcs, Screws 3pcs, nut 1pc, Components Layout Circuit 1pc)..

Plastic Cable Gland PG 9 - Cord Grip Connector for cable fixing, machinery control boxes, distribution panels, electrical appliances etc.
Model: PG9, Cable Range: 5mm-8mm, Thread OD: 15mm, Overall Length: 32mm, Material: Plastic, Color: Light Grey..

2A Full Wave Bridge Rectifier Power Supply PCB (Copper Pour) with Toner Transferred, Ready for Etching.
Size: 1.9"x2.9" (49mm x 74mm), Track Width: 2.25mm, Copper Pour Clearances: 1.5mm. PCB Etching: No, PCB Drilling: No
Components Required: Diode 1N5408 (4pcs), Capacitor 2200uF, 3300uF Or 4700uF (1pc), Capacitor 100nF - 100V (1pc), LED 5mm Red (1pc), Resistor 0.5W 1.5K (1pc), 2 Way PCB Terminal Block (1pc), 4 Way Multi-color Red+Black PCB Terminal Block (1pc).
Note: You can change the components according to your requirement..

MAX7219 LED Matrix - 8-Digit LED Display Drivers PCB with green masking and legend printing.
Size: 3.2cm x 5cm, PCB Material: FR4 Dual Side..

30A Heavy Duty High Quality - 4mm Nickel Plated Brass Insulated Speaker Binding Post - Banana Socket Chassis Mount.
Quantity: 1pc Black + 1pc Red..

Diode Based OR Gate Circuit on Dot Matrix General Purpose PCB (Assembled Full Working Project)
Components Used: Tact Switches, LED's, Resistors, Diodes, Connector, Battery, Dot-Matrix PCB etc.
Project Content: Assembled Project PCB - 1pc, Battery Cable - 1pc, 9V Battery - 1pc..

Assembled Unregulated Power Supply - Full Wave Bridge Rectifier

This kit is a quick, neat, and inexpensive way to provide a smoothed 3V to 36V, 1A to 8A (Depending on transformer & components), unregulated DC power supply suitable for powering many electronics circuits. It only requires the AC output of a transformer (not supplied).
Input: Green for transformer connection, Output: 2 x Red Positive and 2 x Black Negative
Components Used: PCB (2.9"x3.9"), Diode, LED 5mm, 2.7K 0.5W CFR Resistor, Electrolytic Capacitor, Vishay 100nF 250V Polyester Film Capacitor, 2 Way PCB Terminal Block etc.
Note: You can customized this Assembled Kit by selecting capacitor and diodes from Available Options..

Motor Clamp - Mounting Bracket For BO Plastic Gear Motors - Medium Quality.

2 Transistors 6-LEDs Flasher PCB Only.
Size: 1.9"x2.9" (49mm x 74mm), Components Required: Diode 1N4007 (1pc), Capacitor 22uF 63V (2pcs), LED 5mm Red (3pcs), LED 5mm Green (3pcs), Resistor 0.25W 18K (2pc), Resistor 0.25W 330 Ohm (2pc), Transistors BC547 (2pcs), Variable Resistor (Preset) 10K (1pc), Relimate 2-pin Male Header 5.08mm (1pc), Working Voltage: 9 to 12V DC.
Note:
1.) You can change the components according to your requirement.
2.) You can select available option to Print Your Name on PCB..